- #1
HI all,
I'm at the end of my brew controller build and looking to admit a fan. I'm having issues actually driving the buff, and I think it's due to a lack of Watts. The 80mm 120v AC fans are just far to a fault big for my box indeed I went with a 50mm 12v DC fan but it's causing issues.
Hither is my setup.
This Light-emitting diode device driver is inverting from 120v Ac to 12v DC
120v Ac to 12v DC ~1watt inverter
My fan which is a 50mm 12v DC 1watt fan
https://web.amazon.com/gp/cartesian product/B00006B8CM/?tag=skimlinks_replacement-20
IT's just BARELY spinning. Not enough to be useful. When I put a multimeter to the 12v or 6v bombardment mental test mode and put through the pitch-black/red pins on their respective wires, IT runs perfectly. Any ideas equally to what could make up the issue?
The fan draws 90mA consumption 1.08W which is around the yield of the inverter. Should I get an inverter with much output Watts?
Here's a video of what I'm talking or so. Thanks in advance!
https://youtu.atomic number 4/dsWakD0uDYo
Go edited by a moderator:
- #3
I'm not true what you mean away putting a multimeter on the wires devising the sports fan take to the woods.
Prove the following: while the fan is connected, check the output voltage of the driver. I think IT might be possible that the slightly too high load drops the output voltage.
Another possibility that I could imagine, is that since the number one wood is likely a buck converter, it outputs high frequency noise. The fan probably has some master circuitry, if only because it's a brushless motor, but likely because the control wire of the lover allows the PC to check its speed. This circuitry plausibly expects the smooth, quiet index outturn of the PC PSU. You can endeavor to smooth the exponent by soldering a small capacitor (roughly 100nf is plenty) parallel to the fan's input wires. But I'm really not sure if this is a attainable induce.
- Thread Starter
- #4
This fan doesn't have a thermistor
I'm not sure what you mean by putting a multimeter on the wires making the fan run.
Try the following: while the fan is connected, check the output voltage of the driver. I think it mightiness atomic number 4 possible that the slightly likewise high onus drops the output voltage.
Another possibility that I could imagine, is that since the driver is likely a shoot converter, it outputs altissimo frequency make noise. The fan probably has some master circuitry, if only when because it's a brushless motor, but apt because the control wire of the fan allows the PC to control its speed. This circuitry plausibly expects the wax-coated, noiseless power end product of the PC PSU. You derriere try to smooth the power by bonding a small capacitor (or so 100nf is plenty) duplicate to the fan's input wires. But I'm real not steady if this is a possible have.
The red and black wires from the fan are soldered to the LED driver. I just touched the black multi-meter dig into to the black telegraph and the red multi-meter dig into to the red wire. When it's on 12v battery test it makes the fan run utterly. In the telecasting, the fan going turning happening full speed is when I touched the probes to the wires. I didn't know the multi-meter was supplying any power which was eldritch.
The fan is a ball-bearing lover, does that change things? I think you're right with the slightly too high load falling the output voltage. I'm superficial at a 24w 120v AC to 12v DC 2amp inverter. This inverter can supply the necessary volts to power the rooter.
https://www.amazon.com/dp/B016FG9KWQ/?tag=skimlinks_replacement-20
Last edited aside a moderator:
- #5
The multimeter doesn't supply power in voltage measuring manner A far as I know, no more. What voltage does IT evince when you order it across the leads?
The only thing I send away have in mind is the multimeter smoothing the voltage coming from the driver somehow... That's really weird! Do you receive a capacitor on hand maybe? A non-electrolytic one (i.e. one that doesn't have a polarity), around 100 nf, to see if that has the same effect atomic number 3 the multimeter.
This guide here recommends a current-limiting driver: HTTP://web.instructables.com/id/Office-Microcomputer-Buff-using-LED-Driver/ rather than a flat voltage type. I'm not sure enough why he recommends this, though, and I look this could kill the fan, as that kind of driver would output as much electric potential every bit needed to do the current limit give, which, if the fan wants less current than the driver wants to deliver, leave ramp the voltage up past the safe levels. For all intents and purposes, yours should work, unless the electric potential drops overmuch. But if the voltage drops too much, touching the multimeter probes to the wires shouldn't do anything! I'm rather confused myself now.
- #6
simple resolution? stopover by your local thrift lay in. go the electronics section. they usually make a big ass bin chockful of early superpowe plugs for random electrical appliances, laptops, pin grass, etc.
obtain the appropriate 12VDC transformer with the correct amperage.
telegram it aweigh.
- #7
The driver is 300mA. At 12V that's 3.6W. it doesn't seem the device driver should constitute a problem for supplying enough power. The third lead probably needs to be grounded or tied to the positive supply. Not sure which and it may be possible to fry something if you choose wrong. I got one going once but can't remember what I did.
- #8
Why does the game arranger say 3-14V thereon? Is there an registration screw?
- #9
Hi all,
I'm having issues actually driving the devotee, and I imagine it's referable a lack of watts.
Here is my apparatus.This LED driver is inverting from 120v AC to 12v DC
![]()
120v AC to 12v DC ~1watt inverter
My fan which is a 50mm 12v DC 1watt rooter
It's just BARELY spinning. Not enough to represent useful. Any ideas as to what could embody the emergence?
The sports fan draws 90mA consumption 1.08W which is around the output of the inverter. Should I get an inverter with more end product watts?
On that point are two main types of external LED drivers, constant current and constant potential.
Constant-current drivers power LEDs that require a fixed output current and a range of output voltages.
There will beryllium only one output signal current specified along with a range of voltages that will vary depending on the load (wattage) of the LEDs.
Yours is a steadfast current with an output voltage range from 3 V to 14 V not a fixed voltage.
To get around the 14 V you need to increase the load up-to-date close to the rife listed on the twist. Get a constant voltage LED device driver or buy a regular power provision along ebay.
Last edited by a moderator:
- #10
Zealous point ClaudiusB. Hence the 300mA +/- a closed-minded tolerance.
Source: https://www.homebrewtalk.com/threads/120v-ac-to-12v-dc-fan-wiring.628477/